close x

Category Archives: Medical

Alternatives to PPSU and PSU sheets for medical applications, selecting the right material for Sterilization

There are a number of different thermoplastic resins that are used to make sheet for medical applications.  These resins include Polyphenylsulfone (PPSU), Polysulfone (PSU), Polyetheretheketone (PEEK), and Polyaryletherketone (PAEK), as well as many others.  The cost of these resins is often ten or twenty times higher than Polycarbonate resin.  One of the reasons that these resins are selected is their ability to withstand some of the sterilization techniques used in the medical market to destroy living organisms such as bacteria.

The main sterilization techniques include electron beam or gamma radiation, Steam Autoclaving, Ethylene Oxide (ETO) and Vaporized Hydrogen Peroxide (VHP).

Some of the resins such as PPSU and PSU are able to withstand most if not all of the sterilization techniques; however, due to the very high resin cost, this high performance often translates to high prices.  Even though Highline can offer both PPSU and PSU sheets, the aim of this blog post is to look at whether there are more economic alternatives if the finished part only needs to withstand a known sterilization technique.  To do this analysis, we will look at each sterilization technique in turn.

Electron beam or Gamma Radiation

Standard Polycarbonate does not perform well under repeated radiation sterilization.  It tends to loose mechanical properties and yellow.  However, there are some grades of polycarbonate that are designed to resist radiation and reduce the negative effects.  These grades do not have the same level of resistance as PPSU and PSU, but could be an alternative where the product only requires a limited number of sterilization cycles during its life.

Another alternative is Transparent Polyamide.  This material, even though it is more expensive than polycarbonate, is significantly cheaper than PPSU.  Transparent Polyamide has excellent resistance to radiation an would be an ideal choice of material.  HighLine does not currently produce or stock polyamide sheet, however we have previously produced the material and have the production capabilities to make it.  If a customer had a large enough application for this material, we could consider custom production in partnership with the customer.

Steam autoclaving

Standard Polycarbonate is not suited to steam autoclaving.  However, there are high temperature grades of polycarbonate available for superheated steam sterilization.  These grades have typically been produced for the injection molded part market rather than the extruded sheet market.  If a customer had a significant need for this type of extruded sheet, HighLine could investigate whether it is possible to produce sheet from high temperature polycarbonate.

Ethylene Oxide

Polycarbonate has a fair degree of resistance to ETO, however it is certainly not at the level of PPSU and PSU.  If the final product only needs to undergo a limited number of sterilization cycles during its life, polycarbonate may be an option, but full testing would be needed to verify.  For repeated ETO sterilization cycles, transparent Polyamide sheet is an excellent lower cost alternative.  Again HighLine has proved that it has the capability to produce polyamide sheet, but it would need to partner with a customer with a significant demand to make it economically viable.

Vaporized Hydrogen Peroxide

Polycarbonate has excellent resistance to vaporized hydrogen peroxide.  If this sterilization technique is the only sterilization method used on the finished product, there would be no need to consider higher priced materials.


To summarize, if only one or two sterilization techniques are to be used on the finished product, significant cost savings can often be achieved by using lower cost materials than some of the high end thermoplastics such as PPSU and PSU.  Not only does this make the finished items more economically viable, but it also allows them to benefit from some of the other properties of polycarbonate or polyamide such as transparency, clarity and strength.  If a customer has a significant need for material to withstand sterilization, we would recommend that they contact us so that we can have a full discussion on the options.

As a final thought, it could also be possible to add anti-microbial additives to the polycarbonate or polyamide sheet to further improve their use in the medical market.





Medical Uncategorized0 comments